| Názov produktu | Predajca | Popis | ||
|---|---|---|---|---|
| RS232toMBus-5 - Komunikačný prevodník RS232 na M-Bus | Juraj Čaplický - Elektronika | Vzdialené vyčítavanie údajov z M-Bus zariadení prostredníctvom sériovej komunikačnej linky RS232 v priemysle, automatizácii budov. Najčastejšie používané M-Bus slave zariadenia sú merače spotreby tepla, vody a elektrickej energie. | Viac | |
| RS232toMBus-4M - Komunikačný prevodník RS232 na M-Bus | Juraj Čaplický - Elektronika | Vzdialené vyčítavanie údajov z M-Bus zariadení prostredníctvom sériovej komunikačnej linky RS232 v priemysle, automatizácii budov. Najčastejšie používané M-Bus slave zariadenia sú merače spotreby tepla, vody a elektrickej energie. | Viac | |
| T-CON 02.A | MRK s.r.o. | Miniatúrna požiarna ústredňa pre vyhodnocovanie snímača plameňa. Jednotka je napájaná 24 V DC. Obsahuje vstupný obvod pre pripojenie snímača plameňa typu MHG 585.078. Po dohode je možné upraviť aj pre iné typy. Jednotka má k dispozícii reléový výstup, ktorý je zopnutý v stave OK. V ostatných stavoch je relé rozpojené. Je možné využiť aj rozpínací kontakt = otočenie logiky. Signalizačné led na čelnom paneli ohlasujú stav OK, porucha snímača, prerušené vedenie, odpojenie snímača, skrat snímača, komunikáciu. Jednotku je možné vybaviť komunikačnou linkou RS485, a stavy prenášať do nadradeného systému. | Viac |
Produkty zo zahraničia
| Názov produktu | Predajca | Popis | ||
|---|---|---|---|---|
| PowerCable Modbus 101x | NETIO products a.s. | NETIO PowerCable Modbus 101x is a smart WiFi power socket and a power extension cable designed by NETIO products. Using the Modbus/TCP protocol, it is possible to switch its power output on/off and read energy consumption remotely over the network. PowerCable connects to the network over WiFi (internal antenna). The output power socket can be turned On/Off over a web interface. The web interface also shows the measured electrical values (V, A, kWh, W, Hz, TruePF) at the metered power socket. PowerCable Modbus 101x supports the M2M Modbus/TCP protocol for controlling its output and reading the measured values. Modbus/TCP is a popular M2M protocol used in the industry world-wide. To increase security, PowerCable Modbus contains a built-in IP filter. The IP filter limits the range of IP addresses that are allowed to access the device using the Modbus/TCP protocol. The WiFi power cable supports IOC (Independent Output Control); the state of the output is not affected by weak WiFi signal, restart of the WiFi module, or even firmware upgrade. The power-up state of the smart power socket is configurable (On/Off/Last). An important feature for industrial control is ZCS (Zero Current Switching). This feature ensures that the relay is switched only when the immediate current value passes through zero. This feature ensures long-term durability even when switching capacitive loads (switching supplies common in ICT) or inductive loads (transformers, motors). The operating temperature range of NETIO PowerCable Modbus 101x is -10 to 65°C (at 65°C, the maximum current is limited to 5A). Electrical measurements (readings accessible over Modbus/TCP and the web) No special mobile application is needed for installing the WiFi controlled outlet and connecting it to a WiFi network. PowerCable Modbus works as a WiFi AP and a web based wizard will guide you through the configuration, including the selection of a WiFi network from a list. The setup process is simple and fast. | Viac | |
| NETIO PowerCable IQRF 901x | NETIO products a.s. | NETIO PowerCable IQRF is a smart power extension cable that communicates over the IQRF LPWAN network (868 MHz). The 230V/16A electrical socket features electricity metering (A, V, W, TPF, kWh, Hz) and can be switched on and off with full IQRF Interoperable support. Using the Smart connect function, PowerCable IQRF can be connected to the IQRF wireless network. The DPA protocol can be used to control the output or read the measurements (V, A, kWh, W, Hz, TruePF). PowerCable IQRF is constantly powered, so it also acts as a message repeater in the IQRF MESH network. PowerCable IQRF 901x supports IQMESH functions of the IQRF wireless network. The device supports the “IQRF Interoperable” DPA standard for sensors and I/O devices. The IQRF outlet supports IOC (Independent Output Control); output state is unaffected by firmware update. The PowerUp state function allows to specify the desired output state after power up (On / Off / Last). The Last option stores the last state of the output (on or off) before a power outage, and restores it when the power is restored. An important feature for light industrial use is ZCS (Zero Current Switching). This feature ensures that the relay is switched when the current passes through zero level. PowerCable IQRF 901x can be used at ambient temperatures from -10 to +65°C. | Viac | |
| PowerPDU 4C: PDU with energy metering and open API | NETIO products a.s. | NETIO PowerPDU 4C is a smart PDU (Power Distribution Unit) with four power outlets (4x IEC-320 C14). Each output can be controlled and metered independently. PowerPDU 4C includes a 2x LAN Ethernet switch and a serial port (RS-232). NETIO PowerPDU 4C can be mounted in rack cabinets (horizontally and vertically). Four different rack-mount brackets are available. PowerPDU 4C offers an open M2M API with 13 different M2M protocols that can be used for energy consumption metering and control of individual outputs. NETIO 4x smart power outlets can be connected to multimedia AV systems, cloud services (e.g. MS Azure IoT hub), the Node-RED environment, or smart home apps. Each of the four power outlets (IEC sockets) can be switched on/off with a button at the device or from the device’s web interface. The manufacturer provides a mobile app; however, the open API also allows the use of recommended third-party apps. | Viac |
Výsledky vyhľadávania v článkoch